Ask three people how many outlets can go on one circuit and you may hear three different numbers. In Ontario the answer comes from the Ontario Electrical Safety Code (OESC). The provincial regulation behind it, O. Reg. 164/99, adopts the Canadian Electrical Code Part 1, C22.1:24, as amended by the Ontario amendments dated June 12, 2024. The Electrical Safety Authority (ESA) explains how individual rules apply in its bulletins, each written against a particular edition, so an electrician will confirm a rule against the code in force when the work is done.
The short version: when the loads on a circuit are unknown, the code sets a maximum count of outlets per circuit, and that count depends on how the breaker or fuse is marked. When the loads are known, the count can be higher, as long as the total stays within what the breaker is rated to carry continuously. Everything below comes from ESA publications, quoted or closely described, with the links listed under Sources.
How many outlets on a 15 amp circuit in Ontario
ESA's Bulletin 8-3-15 sets out the base rule, Rule 8-304, in these words: it "does not permit, on any 2-wire branch circuit where the loads are unknown, the number of outlets to exceed 12 per 15 A branch circuit where the OCPD is unmarked (or marked 80% continuous operation rating) and 15 outlets per 15 A branch circuit where the OCPD is marked for 100% continuous operation."
OCPD means overcurrent protective device, which in a house is usually the breaker or fuse in the panel. So the label on that device decides whether the starting figure is 12 or 15. If you cannot tell which marking your breaker carries, treat that as a question for an electrician rather than a guess.
The same bulletin explains where the number comes from. Where the loads are unknown, outlets are considered to be 1 A loads. A separate ESA guideline on luminaire displays gives the matching limit on the breaker side: a 15 amp overcurrent device that is not marked at 100% can only be loaded to a maximum of 12 amps. Twelve outlets counted at 1 A each add up to exactly that 12 A ceiling, so the two figures line up.
When more outlets are allowed: known loads
The count is a stand-in for load, used when nobody can predict what will be plugged in. Bulletin 8-3-15 says Subrule 3) "permits the maximum number of outlets to exceed the prescribed number of outlets in Subrule 1), provided that the load is known and that it does not exceed the maximum continuous operation rating of the OCPD."
Smoke alarms show how the counting works on a mixed circuit. The bulletin says that for branch circuits where the load is unknown, such as circuits that supply a mix of lighting and general purpose receptacles, each smoke alarm shall be counted as one outlet.
The flip side matters just as much. A circuit can sit well under its outlet count and still be overloaded by what is plugged into it. ESA's power bar factsheet warns against using multi-plug devices with relatively high-load appliances, or where running two appliances at once on the same circuit may overload the branch circuit and trip the breaker. Its examples include microwaves, vacuum cleaners, toasters, irons and portable space heaters.
How many outlets on a 20 amp circuit
This is where we have to be careful. The ESA bulletin text we could confirm gives the outlet counts for 15 A circuits only. We did not find an ESA or CSA Group excerpt that states the count for a 20 A circuit in wording we could verify, so we are not going to quote a number here.
What does carry over is the principle. The known-load subrule is written around the continuous operation rating of the OCPD, not around a particular amp size, and the 1 A per outlet assumption applies wherever the loads are unknown. A Licensed Electrical Contractor can tell you how Rule 8-304 applies to a specific 20 A circuit in your home, including whether its breaker is marked for 80% or 100% continuous operation.
Have electrical work in mind? Get a free quote.
Licensed & Insured | ECRA/ESA 7014730
Dedicated circuits: kitchens and other appliance outlets
How many outlets per circuit is only part of the picture, because some outlets are not supposed to share with general receptacles at all. The kitchen is the clearest case.
Refrigerator. ESA's Bulletin 26-23-6 says the code requires at least one branch circuit for receptacles installed for refrigerators in the kitchen of a dwelling unit, under Rule 26-722 d) i). It also allows a single duplex receptacle for side-by-side refrigerators or freezers, and says receptacles intended to supply a mini-fridge, beverage cooler or a freezer in a dwelling kitchen are permitted to be fed from a refrigerator branch circuit.
Counter. The same bulletin refers to branch circuits supplying receptacles installed at the kitchen counter, required by Rule 26-722 d) iii).
Other appliance outlets. A dedicated circuit for a single appliance still has to meet the arc fault rules. ESA's Bulletin 26-18-13 asks whether AFCI protection is required for receptacles not specifically exempted, such as those for a dedicated microwave, dishwasher, or garbage disposal unit, and answers yes.
If a kitchen renovation moves the fridge, adds an island or adds counter length, check what those changes mean for the circuits before the walls close.
Adding outlets to an existing circuit
Extending an existing circuit, say for a basement, home office or addition, comes with its own requirements, set out in ESA's Bulletin 26-29-6. When receptacles are added to an existing circuit and the existing part is left unchanged, arc fault protection is required for the extension of the branch circuit. An AFCI receptacle, or a dead front, is required at the first added receptacle on the extension. ESA also recommends either an AFCI breaker on the circuit or replacing the first existing receptacle with an AFCI receptacle.
The new devices must also be tamper resistant outlets. The bulletin states that added receptacles are required to be tamper resistant and so marked.
Older wiring brings its own limits. ESA's flash notice on knob and tube wiring lists adding receptacles and outlets on existing circuits among the improper connections it sees, and says this work should be done by a Licensed Electrical Contractor.
Signs a circuit is carrying more than it should
A breaker that shuts off is often the first clue. ESA's product safety tips say tripped breakers may point to too many items on one circuit. If yours trips repeatedly, our post on why a breaker keeps tripping walks through the usual causes and which ones need an electrician.
ESA's Homeowner Electrical Safety Handbook describes octopus outlets, ones with too many devices plugged in, as able to overheat and present a hazard, and its advice is to contact a Licensed Electrical Contractor to add additional outlets or circuits. ESA's cottage safety page makes the same point about cords: extension cords are for temporary use only, and it is safer to have an LEC install permanent wiring and outlets.
A single dead receptacle is a different problem from an overloaded circuit, and our outlet not working post covers that case. If the real issue is that the panel has no room left for the circuits a renovation needs, our post comparing 100 amp and 200 amp panel upgrades explains how that decision is made.
Who can add a circuit or outlet in Ontario
Adding an outlet or running a new circuit counts as electrical work. Under ESA's DIY guidance, a homeowner may wire their own home if they first file a notification with ESA and the work is then reviewed. A friend, a relative or a handyman is not allowed to do it for you, and anyone you hire needs an ECRA/ESA licence.
KV Bear Electrical (ECRA/ESA 7014730) plans circuits for kitchens, basements and additions, adds dedicated circuits for appliances, and can review an existing panel and its circuits during an electrical inspection. Call 905-999-5048 or request a quote.
Frequently Asked Questions
Is 12 the most outlets I can put on a 15 amp circuit in Ontario?
Twelve is the limit ESA describes for a 2-wire 15 A circuit with unknown loads when the breaker is unmarked or marked for 80% continuous operation. ESA's Bulletin 8-3-15 gives 15 outlets where the breaker is marked for 100%, and allows more where the load is known and stays within the breaker's continuous operation rating.
Do hardwired smoke alarms count toward a circuit's outlet total?
On a circuit with unknown loads, such as one mixing lighting and general receptacles, ESA's Bulletin 8-3-15 says each smoke alarm counts as one outlet. Where the load is known, the general known-load subrule applies instead, as long as the total stays within the breaker's continuous rating.
Can a beverage cooler share the kitchen fridge circuit?
ESA's Bulletin 26-23-6 says receptacles intended for a mini-fridge, beverage cooler or freezer in a dwelling kitchen are permitted to be fed from the refrigerator branch circuit.
Do outlets added to an existing circuit need AFCI and TR protection?
Yes, according to ESA's Bulletin 26-29-6. The extension needs arc fault protection, with an AFCI receptacle or dead front at the first added receptacle, and the added receptacles must be tamper resistant and marked TR.
What is the outlet limit for a 20 amp circuit?
We did not find an official ESA or CSA excerpt stating the 20 A count in wording we could verify, so we do not quote one. Ask a Licensed Electrical Contractor to check how Rule 8-304 applies to your circuit and its breaker marking.
Sources
- ESA OESC Bulletin 8-3-15: Maximum circuit loading and demand factors
- ESA SPEC-010 R1: Guidelines for Displays of Luminaires for Sale
- ESA Electrical Safety Factsheet: Power Bar and Multi-Plug Devices
- ESA OESC Bulletin 26-23-6: Kitchen receptacles
- ESA OESC Bulletin 26-18-13: AFCI protection questions
- ESA OESC Bulletin 26-29-6: Electrical replacements and alterations in dwelling units
- ESA Flash 19-16-FL: Knob and tube wiring in residential installations
- ESA: Product Safety Tips for Consumers
- ESA Homeowner Electrical Safety Handbook: Inside Your Home
- ESA: Cottage Safety
- ESA: Do-It-Yourself (DIY) Electrical Work
- Ontario e-Laws: O. Reg. 164/99, Electrical Safety Code
Facts checked November 16, 2026.
KV Bear Electrical Inc. is a licensed residential electrical contractor (ECRA/ESA 7014730) based in Oshawa, Ontario. The facts here come from the official sources listed above. Have a question about your home? Call 905-999-5048.
Related Services:
Related Guides
GFCI Outlet Guide: What It Does, Where It Goes and TR Ratings
A GFCI outlet looks like any other receptacle with two buttons added, but it does a very different job. Here is how it detects a ground fault, where ESA says Ontario homes need one, what the TR marking means, and how to tell when a unit has stopped protecting you.
Read the guideWhen to Replace an Electrical Panel: 7 Signs to Watch For
Age alone rarely decides it. Watch instead for seven signs that point toward a new panel. Then check what Ontario's Electrical Safety Authority says about older fuse panels, and which official notices actually name panel brands.
Read the guidePigtailing Aluminum Wiring vs Full Replacement: Safety, Connectors and Cost
Pigtailing and full copper replacement both deal with aluminum wiring, but they are different jobs. How does a pigtail work, what do ESA and the U.S. CPSC say about connectors, and which of the two suits your house?
Read the guide